Wind Turbine Water Heating
Wind Turbine Water Heating
Heat water directly using a wind turbine generator (with or without a battery bank)
wind | heating | waterWind turbine generators are used primarily for electricity generation. The power used can be stored in a
battery bank or connected to the mains supply using a suitable
grid tie inverter. In very strong winds, and/or when the batteries are fully charged a wind turbine may generate more current than the batteries can handle. Therefore a
dump load is often used to divert the extra energy to heat water so it is not wasted and so that the wind turbine does not spin so quickly that it is damaged.
Diversion Load Water Heating
Pictured above is a typical
12V water heating element (200 Watt power) which can be screwed into an immersion heater
draincock hole. When used as a diversion (dump) load, such an element is connected to the batteries via a charge regulator. When the
regulator detects that the batteries are fully charged, it diverts the generated electricity to the
element which heats water.
Direct Wind Turbine Water Heating
It is not usually possible to connect a
12 Volt water heating element directly to the output from a
wind turbine. The voltages generated by a 12 Volt wind turbine are typically far in excess of their nominal 12 Volt rating - with values of over 50 Volts often recorded in
heavy winds. These high voltages would rapidly burn out the
heating element when you need it most. A 12 Volt heating element should be used with just 12-15 Volts, a 24V heating element with just 24-30 Volts.
In order to prevent the
heating element from receiving fluctuating
over-voltages a
small battery should be used as a
buffer between the wind turbine output and the heating element. A
12V motorcycle battery is perfect for this task (for
12V immersion elements) - no more powerful than
4 amp hours / 50 cold cranking amps, and it should be a
lead-acid battery which can be refilled with water. A sealed gel type battery or dry cell should
not be used.
The
heating element chosen must be
closely matched to the typical
power output of the wind turbine. If the element is too large (high wattage), the wind turbine will not be able to start up spinning unless the wind is very strong. If the element has a low wattage, nothing will be damaged since the small battery will limit the voltage to around 12v, but heat will be dissipated in the wind turbine generator and cables rather than used to heat water.
If the heating element is poorly matched then there is the risk of a large
voltage drop between the
wind turbine generator and the immersion heating element causing the cable between them to
melt. In this eventuality the wind turbine would then
freewheel at very high RPM and could easily be damaged to destroyed.
Buy an Immersion Heater Element for a Wind Turbine
Click here to view our new article
Immersion Heater Elements for Wind Turbines in which we present some of the latest 12V, 24V, 36V, and 48V
immersion heater elements on the market.
Article Last Modified: 13:21, 4th Sep 2008Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Immersion Heater Elements for Wind TurbinesDetails of a range of immersion heater elements designed for use with wind turbine generators
Article Last Modified: 08:19, 22nd Dec 2008wind | heating | water200W 12V Immersion HeaterUsing a wind turbine to heat water for your home via an immersion heater element
Article Last Modified: 13:21, 4th Sep 2008heating | wind | waterThermosyphon Solar Water HeatingFind out how a Thermosyphon Solar Water Heating System works
Article Last Modified: 16:15, 3rd Nov 2008heating | solar | waterSimple Solar Water HeatingMake a simple solar water heater with easy to find materials
Article Last Modified: 13:17, 30th Jun 2008heating | solar | waterPVC Wind Turbine BladesLearn how to make your own PVC wind turbine blades
Article Last Modified: 15:16, 19th Aug 2008windPermanent Magnet GeneratorBuild a wind or water power system with around a PM Generator
Article Last Modified: 11:44, 21st Jul 2008wind | hydroDIY 2kW Wind TurbineRead about a home built 2kW wind turbine constructed from scrap
Article Last Modified: 08:46, 4th Oct 2007wind | recyclingDIY Solar Water Heating PrototypeFollow the construction of a successful DIY solar water heating prototype
Article Last Modified: 15:16, 19th Aug 2008solar | heating | waterSimple Solar Water Preheating SystemUse solar power to pre-heat water and reduce electricity/gas consumption
Article Last Modified: 14:47, 7th Oct 2009solar | heating | waterInterconnecting Batteries for Battery BankFind out how best to connect batteries together into a battery bank
Article Last Modified: 13:53, 23rd Feb 2007storage
|
|
|
