What is a Shunt
What Is A Shunt
Find out what is a shunt resistor and how it is used in RE applications
electric circuit | education
A
shunt (aka a
current shunt resistor or an
ammeter shunt) is a high precision
resistor which can be used to measure the current flowing through a circuit. Using
Ohm's Law we know that the voltage dropped across a resistor divided by the resistance of that resistor is equal to the current, therefore if we measure the voltage across a
shunt resistor in a circuit, we can easily calculate the current.
For example, pictured above is a typical
100 Amp Shunt Resistor. This can be used to measure currents of up to 100 Amps - although to prevent overheating it should really only be used to measure continuous currents of no more than 60-70 Amps.
*
If a shunt resistor overheats it can permanently change the resistance of the shunt.
This shunt is calibrated such that the
voltage drop across it is 100mV when the current flowing through it is 100 Amps. Therefore we can calculate the resistance of this shunt to be voltage divided by current = 0.1 / 100 = 0.001 Ohms (typically to within ± 0.25% accuracy). Therefore if a voltage drop of 28mV is measured (using a standard
multimeter or 0-100mV range voltmeter), we know that the current flowing is 0.028/0.001 = 28 Amps.
(The power
wasted by the shunt resistor is given by multiplying the voltage by the current = 0.028 * 28 = 0.78 Watts in this example.)
To save making this calculation manually each time it is possible to re-label a 0-100mV
moving coil voltmeter so it instead reads 0-100 Amps. This would be achieved simply by sticking the word "Amps" over "mV" on the face of the meter which would now be an
ammeter rather than a
voltmeter.
Using a Shunt Resistor in a Renewable Energy System
It is very important to know how much current is flowing in and out of the
battery bank in a renewable energy system. When charging the current flowing into the batteries should never be more than 10% of the battery capacity - e.g. a 100Ah battery should not be charged with more than a 10 Amp current or it may be damaged and/or overheat.
It is also very useful to know how much current is being generated by a
wind turbine or
solar panel, because that information helps you to calculate how much
power is being generated. For example a 12 Volt 15 Watt
PV Solar Panel may produce a voltage of 18 Volts when it is very cloudy and 21 Volts when it is very sunny.
When it is cloudy you may measure a current of just 0.1 Amps and when it is sunny a current of 0.8 Amps. Power is equal to voltage multiplied by current, so the solar panel is generating just 2 Watts when it is cloudy and almost 17 Watts when it is sunny.
Make Your Own Shunt Resistors
It is possible to
Make a Basic Shunt Resistor very cheaply with some copper wire. Click here to find out more.
Article Last Modified: 12:52, 28th Feb 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Make a Shunt ResistorMake your own rough and ready shunt resistor
Article Last Modified: 12:52, 28th Feb 2007electric circuit | educationBasic Ammeters and VoltmetersFind out how to monitor the health of your RE system's generator and batteries
Article Last Modified: 18:17, 26th Feb 2007electronics | storage | wind | solarOhms LawLearn about Ohm's Law and how it is used in Renewable Energy systems
Article Last Modified: 12:15, 23rd Feb 2007electric circuit | educationMake a Simple Battery Status MonitorMonitor battery status with this easy electric circuit project - no skill required!
Article Last Modified: 12:33, 16th Mar 2007storage | electric circuitThree Phase BasicsGet an understanding of three phase wiring in wind turbine alternators
Article Last Modified: 15:13, 19th Aug 2008wind | electric circuit | websitesAWG to Square mm Wire Size ConverterConvert between AWG, inches and mm diameter, and square mm area measures of wire size
Article Last Modified: 06:45, 19th Jul 2008storage | electric circuit200W 12V Immersion HeaterUsing a wind turbine to heat water for your home via an immersion heater element
Article Last Modified: 13:21, 4th Sep 2008heating | wind | waterPower InvertersFind out about the uses of power inverters in renewable energy generation
Article Last Modified: 16:41, 21st Jul 2008storage | general | electronicsWhat is a Zener DiodeFind out more about the Zener diode
Article Last Modified: 10:20, 10th Feb 2009electric circuit | educationInterconnecting Batteries for Battery BankFind out how best to connect batteries together into a battery bank
Article Last Modified: 13:53, 23rd Feb 2007storage
|
|
|
