What is Wind Turbine Furling
What Is Wind Turbine Furling
Understand how Furling works to protect a wind turbine from high winds
wind | educationWind Turbines are designed to take the energy of the wind and convert it into useful electricity - the stronger the wind the better
usually. If the wind is too strong then a turbine can spin so fast it destroys itself with
turbine blades ripped off, the
alternator damaged by excessive heat, and damage to the
turbine tower.
Furling is one method of preventing a
wind turbine from spinning too quickly simply by turning the blades away from the direction of the wind.
Furling can be achieved either manually (by the turbine owner himself physically cranking the turbine out and away from the wind), or automatically (with hydraulics and springs for example) with the goal of turning the turbine blade edges into the wind when the wind is dangerously strong and gusty.
Wind Turbine Furling
The simplest way of
furling a wind turbine is a passive system in which the turbine is yawed sideways away from the wind as maximum power is reached.
Slightly more complicated and with more moving parts and stressed components weights are added to the tail and a springed hinge to the point where the wind turbine alternator meets the mast. When the wind is very strong, it will blow over the turbine pushing it out of the wind. By adjusting the strength of the spring and the weights on the tail, you can fine tune the exact furling wind speed your require.
The larger and more powerful the
wind turbine generator, the more complicated (and important) furling becomes. Some turbines even have motors on each blade to automatically turn them edge-on to strong winds.
Above is a photograph (from
CFCCREL) of a
small wind turbine generator furled (turned) out of the wind. The direction of the wind can be seen by the position of the wind turbine tail - i.e. the wind is hitting the turbine at 180 degrees to the angle of the tail. The wind turbine
blade edges are therefore facing the wind which is exactly what we want - the minimum surface area possible facing the wind, and the turbine not over-spinning.
Article Last Modified: 16:22, 19th Dec 2006Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
DIY 2kW Wind TurbineRead about a home built 2kW wind turbine constructed from scrap
Article Last Modified: 08:46, 4th Oct 2007wind | recyclingPermanent Magnet GeneratorBuild a wind or water power system with around a PM Generator
Article Last Modified: 11:44, 21st Jul 2008wind | hydroFree VAWT Wind Turbine PlansMake your own 250 Watt vertical axis wind turbine (VAWT)
Article Last Modified: 14:47, 17th Feb 2009wind | educationWorlds Largest Wind Turbine GeneratorRead about the world's biggest wind turbines - 5MW
Article Last Modified: 14:24, 6th Jan 2007windEnamelled Magnet WireFind out more about the wire used to wind coils for generators and alternators
Article Last Modified: 14:34, 5th Apr 2007general | shoppingCalculation of Wind PowerCalculate the power of the wind hitting your wind turbine generator
Article Last Modified: 15:06, 18th Apr 2008wind | educationPVC Wind Turbine BladesLearn how to make your own PVC wind turbine blades
Article Last Modified: 15:16, 19th Aug 2008windHow I Built A Wind TurbineRead how a wind turbine was built for under US$150
Article Last Modified: 15:16, 19th Aug 2008wind | educationBuying Neodymium MagnetsBuying neodymium magnets in the UK
Article Last Modified: 10:15, 23rd Jul 2008general | wind | wavePhotos of PVC Wind Turbine BladesPhotographs of PVC wind turbine blades
Article Last Modified: 13:09, 22nd Dec 2006wind
|
|
|
