Water Pump Hysteresis Circuit
Water Pump Hysteresis Circuit
A simple circuit to prevent a pump being damaged by being turned on and off rapidly (multiswitching)
water | electronics | electric circuitIn our articles
Float Switch Water Level Measurement and
Automatic Pump Shut Off Circuit we looked at simple ways of controlling a
pump automatically according to the level of water in a tank.
We mentioned in the second of those articles that a pump can be destroyed when it's run dry - i.e. when there is no water to pump. Another way to reduce the life of a pump (and also to waste power) is to switch it on and off rapidly (
multiswitching). For the first few seconds after a pump is started, a lot of power (up to three times the power used when it is up and running) is necessary.
When using a
Float Switch or
Liquid sensor there is always the risk that turbulence in the water (caused by the container being moved, or by water being pumped into it) will cause the sensor to turn on and off rapidly as the water sloshes about. If the sensor is used to control a
pump, then the pump will also be turned on and off rapidly. In this article we will look at a circuit which provides a
time delay between the water level being reached and the pump being activated.
Time Delay Pump Controller
This circuit is designed to operate very simply. When the water level reaches the point necessary to trigger the float switch or liquid sensor, a
timer is started. If during the following
10 seconds the switch/sensor
does not switch off, a
relay will be triggered which will in turn feed power to the pump turning it on.
Whenever the switch/sensor turns off (i.e. whenever the water level falls below the preset value even for a split second) the 10 second delay timer will start again from zero. Therefore, it will be
impossible for the
pump to toggle on and off rapidly.
To achieve the desired result an
NE555 integrated circuit (IC) can be used as a timer. This IC (click here for full
NE555 Specifications) can output up to
200mA of current - easily enough to energise the coil of a typical
12 Volt relay. The technical desciption of its use in this application is
monostable operation delay on - i.e. after a delay, the IC will output a continuous positive current until its power supply is cut.
The length of the
time delay is set by adjusting the values of the
resistor and
capacitor according to the following formula:
| Time Delay (secs) = 1.1 x R (kOhms) x C/1000 (uF) |
Therefore, for our target 10 second delay, we can use a
100 kOhm resistor with a
100 uF capacitor. For a shorter delay use a lower value resistor, and for a longer delay use a higher value resistor - for example, a 47 kOhm for a 5 second delay, and a 220 kOhm for a 20 second delay.
Connecting everything up for the final system is also very simple. The 12V supply voltage passes through the
float switch or
liquid sensor and into our circuit. The output (from pin 3 of the NE555 IC) connects to one end of the
relay coil * with the other end connected to the ground (labelled 0V).
*
Note in the diagram below the diode running parallel to the relay coil to protect the NE555 from high voltage spikes when the coil is de-energised..
The
relay can be fitted onto the circuit board with the NE555 chip, resistor, and capacitors making a simple
plug-and-play integrated unit as shown below.
Buying a Pump Time Delay Circuit
If you would like to purchase a complete soldered circuit pre-set with a
10 second (or any other) time delay, a
fitted relay and an LED
water-detected indicator for
£9.99, contact
neil@reuk.co.uk. We sell a range of complete circuits in the
REUK Shop, as well as
liquid sensors and
float switches.
Article Last Modified: 14:54, 19th Nov 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Automatic Pump Shut Off CircuitPut together an automatic system to switch off a pump when there is no more fluid left to pump
Article Last Modified: 14:54, 19th Nov 2007water | electric circuitRelays and Renewable EnergyFind out more about relays and their uses in renewable energy applications
Article Last Modified: 10:50, 24th Oct 2008electric circuit | electronics | generalPumps for Irrigation and Rainwater HarvestingFind out how to choose a submersible pump for irrigation and rainwater collection systems
Article Last Modified: 15:16, 19th Aug 2008water | shopping | generalFloat Switch Water Level MeasurementFind out how to use float switches in renewable energy applications
Article Last Modified: 12:07, 28th Jul 2008water | electric circuitSimple Well Pump ControllerFind out how to automatically get water from the well into a header tank
Article Last Modified: 11:52, 1st Oct 2008water | electronics | electric circuitPower 12V LED Spotlight with 4 AA BatteriesUse a DC-DC converter to step up the voltage from 4 AA batteries to light a bright 12V LED spotlight
Article Last Modified: 11:41, 22nd May 2007lighting | electronics | educationSimple Sump Pump ControllerPut together a sump pump controller with two float switches and NO electronics
Article Last Modified: 08:58, 5th Aug 2008water | electric circuit | electronicsPhotos of PVC Wind Turbine BladesPhotographs of PVC wind turbine blades
Article Last Modified: 13:09, 22nd Dec 2006windTimer Circuits With 4060BBuild a reliable timer to switch devices on and off - from 30 seconds to 24 hours
Article Last Modified: 09:58, 15th Aug 2009electronics | electric circuitReed SwitchesFind out more about reed switches and their uses in RE
Article Last Modified: 09:54, 4th Apr 2007electric circuit | electronics | wind
|
|
|
