TL431 Battery Voltage Monitor
TL431 Battery Voltage Monitor
Monitor the voltage of a battery or battery bank using an TL431 (aka LM431) shunt regulator
storage | electric circuit | electronics
An
TL431 (pictured above) is an
Adjustable Precision Zener Shunt Regulator. Its output voltage can be set to any value between 2.5V and 36V with the use of two external
resistors (acting as a
voltage divider).
With very sharp turn-on characteristics, the
TL431 is an excellent alternative to a
zener diode in many applications. In this article we will look at how a
TL431 can be used to make a very simple
battery status monitor.
Click here to view our article on
making a battery status monitor with a zener diode.
The full
National Semiconductor LM431 Datasheet (PDF) can be viewed by clicking here.
Note that the TL431 is also often labelled as a LM431
and may also be described as a programmable voltage reference.
Using the TL431
The TL431 is most commonly found in the
TO-92 packaging pictured at the start of the article - a piece of black plastic out of which emerge three legs. Below the connections are labelled -
REF is the voltage reference.
..and here below is shown the way the TL431 is represented in
circuit diagrams
TL431s can be purchased cheaply from almost any stockist of electronic components worldwide. We also have them available for sale in the
REUK Shop.
TL431 Voltage Monitor Circuit
Above is shown the circuit diagram for this
TL431-based
voltage monitor. The aim of the monitor is simply to light up an
LED when a target voltage is reached - perfect for a
solar battery charger to let you know when the batteries have reached full charge.
The simple equation displayed above gives the
high limit - in this case the voltage at which the
LED will light up. Since the reference voltage (Vref) is fixed at 2.5 Volts in the TL431, the two resistors are simply selected to provide the desired result.
For example, if you require the LED to light up when the input voltage reaches 7 volts, R1 could be set to 1K8 (1,800 Ohms) and R2 to 1K. Multiplying 2.5 by (1+ (1800/1000)) gives 7.0 Volts exactly as required.
Ideally the R1 and R2 resistors used should both be well over 1K Ohm to ensure that the
reference input current stays below its
10mA safe use limit.
The resistor labelled
R4 in parallel with the LED prevents the LED from glowing softly when the input voltage is still below the
switch-on voltage. We used a 1K Ohm resistor in our experiments successfully. (The lower the resistance value used for R4 for sharper the
switch-on - i.e. a tiny increase in voltage causes the LED to suddenly light up brightly).
The
R3 resistor is there to protect the LED from
excessive current - we used a 500 Ohm resistor, but the value selected depends on the specification of the LED used and the brightness required.
Testing the Voltage Tester
Below is a photograph of a
voltage monitor put together on
prototyping breadboard using the
LM431 to light up an LED when a voltage of
6.25V is reached.
A 1K5 and a 1K resistor were used as
R1 and
R2 respectively to achieve the desired 6.25 Volts limit. A
variable voltage source was then used to test the circuit. When the input voltage was 6.26 Volts the LED lit up (as shown above), and when the input voltage fell to 6.25 Volts the LED switched off completely (as shown below).
The accuracy of the voltage monitor depends on the accuracy of the resistors used. Fine tuning can be achieved using a
variable resistor in series with either
R1 or
R2.
Article Last Modified: 16:42, 11th Jun 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Make a Simple Battery Status MonitorMonitor battery status with this easy electric circuit project - no skill required!
Article Last Modified: 12:33, 16th Mar 2007storage | electric circuitShunt RegulatorFind out about the uses of shunt regulators and dump load controllers in renewable energy applications
Article Last Modified: 15:13, 19th Aug 2008electronics | electric circuitLow Voltage Battery Disconnect CircuitsFind out more about low voltage battery disconnect (LVD) circuits - used to protect batteries
Article Last Modified: 15:04, 28th May 2009electric circuit | electronics | storageBasic 4 AA Solar Battery Charger PlansMake a simple solar charger for 4 AA rechargeable batteries
Article Last Modified: 09:43, 30th Jul 2007solar | educationDC Voltage Multiplier Circuit PlansBuild a circuit to boost the voltage of a DC power source using a MAX756
IC Chip
Article Last Modified: 09:06, 10th Jul 2008electric circuit | electronics | educationSolar Battery Charger With LM317TFind out how to make a current controlled solar battery charger using an LM317T
Article Last Modified: 09:34, 30th Mar 2007solar | education | electric circuit12 Volt Battery Low Indicator LM741Plans for a battery low indicator for a 12 Volt battery using an LM741 operational amplifier
Article Last Modified: 10:17, 28th Jul 2007electronics | electric circuit | generalLM741 OpAmp Voltage IndicatorPlans for a simple voltage high/low indicator built around an LM741 operational amplifier
Article Last Modified: 09:31, 8th Oct 2007electronics | electric circuit | generalSolar Charge ControllerFind out more about Solar Charge Controllers
Article Last Modified: 11:12, 29th Oct 2009solar | electronics | electric circuitMake a Shunt ResistorMake your own rough and ready shunt resistor
Article Last Modified: 12:52, 28th Feb 2007electric circuit | education
|
|
|
