Solar Pump Controller for Swimming Pools
Solar Pump Controller For Swimming Pools
Read about the new REUK solar pump controller for swimming pool heating
solar | heating | electronics
We have been selling our solar water heating pump controllers now for a few years - see here for details:
Solar Water Heating Pump Controller. While this controller is suitable in most cases it is not ideal for use with
swimming pools. One key difference is the need to set a
maximum temperature to prevent the pool from becoming unpleasantly hot. Therefore, in this article we will introduce our new solar pump controller designed specifically for use with swimming pools.
Solar Pump Controller Features
Our standard solar pump controller is actually quite simple. A
temperature sensor is fitted to the hot water storage tank and another to the outlet from the
solar panel. If the temperature of the solar panel is measured to be hotter than that of the stored hot water tank consistently for 30 seconds, then the pump is switched on. The pump stays on for a minimum of 10 seconds whenever it is turned on (to protect it from being damaged by switching on and off rapidly), and then is turned off immediately if the hot water tank is measured as being hotter than the fluid leaving the solar panel to prevent the stored water being cooled.
For the
swimming pool version (pictured above) new functionality has been added - the ability for the user to programme in a maximum pool temperature. If the temperature of the pool is measured to be above the maximum desired, then the pump will not be turned on no matter what the temperature of the
solar panel. If when the pump is on, the temperature of the pool exceeds the programmed maximum for 10 seconds consistently, the pump is automatically turned off.
Connecting up the System
With our standard
solar water heating pump controller, the two sensors can be glued to the tank and solar panel outlet using heat sink compound. For measuring the temperature of the swimming pool with these
non-waterproof sensors it is necessary to make a
waterproof temperature probe. (Click here to visit our guide to
Making a Waterproof Temperature Probe - an LM335Z temperature sensor fitted inside a stainless steel tube and filled with epoxy potting compound). The finished probe can then be dropped into the pool - ideally in a shady location for accurate temperature measurement.
In order to keep the system as cheap and simple as possible, we do not include a
digital display of the measured temperatures and pump status etc. Instead, if the user would like to have the temperatures displayed we suggest the use of one or more
digital multimeters (available from as little as £4). Simply by measuring the voltage across the temperature sensors where they are connected to the circuit board, the temperature can be calculated since it equals
100 * (measured voltage - 2.73).
Using the Controller
The user can programme the maximum pool temperature using the small push button on the circuit board. By pressing and holding this button down for 1/2 a second, the circuit enters programming mode - red LED on for 2 seconds. When the LED turns off, the user presses the pushbutton
X times where 1 time = maximum pool temperature of 25 degrees Cecius, 2 times = 27 degrees, 3 = 29 degrees, 4 = 31 degrees, 5 = 33 degrees and so on. After a pause of 5 seconds, the red LED flashes
X times to give visual confirmation of the programmed setting. At any time, the user can press the button for less than 1/2 a second for the LED to be flashed
X times as a reminder of the programmed setting.
Whenever the temperature of the pool is above the maximum programmed, the red LED blinks.
The controller uses a
relay to switch the pump. When the relay is energised (closing its internal switch) the green LED is lit to give visual confirmation of its status.
Technical Details
This controller is based around a
PICAXE microcontroller - the
PICAXE-08M. This is powered from a 5.0V regulator and has ADC (analog-digital converter) inputs which can take in the temperature sensor values and convert them into a number from 0-255. The
LM335Z temperature sensors output a voltage which is proportional to its temperature - 2.73V at 0 degrees C, plus 0.01V per degree above zero. Therefore at 25 degrees, the sensor outputs 2.73 + (25 * 0.01) = 2.98V.
The PICAXE ADC assigns a value of 0 for inputs of 0V and of 255 for inputs of 5V. For each (just under) 0.02V increase in input voltage, the value increases by 1. For example, if 2.98V (25 degrees Celcius) is input from a sensor, the ADC (using the command
readadc) converts it to 2.98 / 5.00 * 255 = 152. For the temperature comparison part of the circuit (is panel hotter than tank) the microcontroller just checks whether the voltage input from the solar panel sensor is higher than that from the tank sensor. For the absolute temperature measurement requirement (to prevent pool being heated when it is already above the desired maximum temperature), it checks if the pool is above the maximum temperature.
Buy a Solar Pump Controller
If you are interested in purchasing this or any other bespoke
solar water heating pump controller, please contact
neil@reuk.co.uk with details of your exact requirements. Prices start from around £26 to £40 including the temperature sensors.
Article Last Modified: 16:37, 1st Jun 2009Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Solar Water Heating Pump ControllerBuild an electronic pump controller for a solar water heating system
Article Last Modified: 11:33, 9th Jul 2007water | solar | electronicsBuild a Concentrated Solar Water HeaterPlans for building a cheap advanced solar water heating system
Article Last Modified: 10:14, 12th Apr 2007heating | solar | waterBattery DesulfationFind out how to desulfate/desulphate and rejuvenate lead acid batteries
Article Last Modified: 16:56, 5th Oct 2009storage | electronicsDrayton SHR52120 Solar Thermal ControllerFind out more about (and buy) the Drayton SHR 521 20 solar thermal controller
Article Last Modified: 11:44, 3rd Oct 2009solar | water | heating | electronics | shoppingRepeat Timer CircuitMake a repeat timer circuit with large intervals between ON times
Article Last Modified: 09:58, 15th Aug 2009electric circuit | electronics | generalFreeloader Solar ChargerFind out more about the Freeloader solar charger for mobile phones, iPods, PDAs, and GPS
Article Last Modified: 12:01, 25th Jun 2009solar | shopping | generalSolar Roof TilesFind out about solar cells built into roof tiles / shingles
Article Last Modified: 12:03, 29th Jun 2009solarMake a Stirling EngineMake your own demonstration Stirling Engine
Article Last Modified: 14:37, 17th Apr 2006educationGrid Tie InvertersFind out more about Grid Tie Inverters - connect your RE system to the grid
Article Last Modified: 16:36, 2nd Jan 2007general | wind | solar | electronicsWindmaster 500 Wind Turbine Grid Tie InverterFind out more about the Windmaster 500 - a grid-tie inverter for wind turbine generators
Article Last Modified: 15:19, 1st Jun 2007wind | shopping
|
|
|
