Solar Battery Charger With LM317T
Solar Battery Charger With LM317T
Find out how to make a current controlled solar battery charger using an LM317T
solar | education | electric circuitA small
solar panel makes an excellent
battery charger for AA and AAA rechargeable batteries. Only a few components are required and construction is very simple making this a perfect first
renewable energy project.
Rechargeable AA and AAA batteries have a voltage of around 1.2 Volts when fully charged. Therefore 2 in series gives a total of 2.4 Volts, 4 in series 4.8 Volts. Common solar panel output voltages are 3 Volts (for example the
3V 100ma solar panels in the
REUK Shop), and 6 volts - perfect for charging 2 or 4 batteries respectively.
The Limitations of a Basic Solar Charger
Details on making the simplest kind of
Solar Battery Charger are available here. Unfortunately this set-up has one serious limitation - the solar panel has to be well matched to the batteries to be charged or the batteries may be overcharged. If you later decide to charge batteries with a different capacity, you would need to change the solar panel.
Current
Current is the most important factor in any battery charger. As long as the voltage of the solar panel is greater than the total fully charged voltage of the batteries, the batteries will be charged
. If the current is too little, the batteries will charge very slowly. If the current is too high the batteries will be charged too fast, are at risk of being overcharged, may overheat, and have their usable lifetime reduced. Therefore the next development step is to make a
current limited battery charger.
Safe Battery Charging Current
Since we are still making a simple
solar charger it will not automatically turn off when the batteries are full. Therefore we need to keep the charging current low enough that it will not damage the batteries even when they are fully charged. A current of around 10% of battery capacity gives the right balance of charging speed and safety - for example,
2700mah AA rechargeable batteries should be charged with a current of 10% of 2700 = 270ma. To charge the batteries faster a higher current could be used, but the chance of the batteries being overcharged would increase.
Limiting Current with an LM317T
The
LM317T is a
voltage regulator chip. It can also be used with a suitable
resistor to regulate
current. Full details on how this works are available here in our guide to
using the LM317T with LED lighting.
The value of the
resistor required is given by
Ohm's Law as 1.25V divided by the output current required. (The 1.25V is the regulated output from the LM317T's
ADJ output.) The higher the input voltage and current, the more heat will be generated by the LM317T since the output current is fixed and the extra power has to go somewhere. The LM317T will cope with currents of up to 1.5 Amps and so will have no problem at all with small solar panels.
Choosing the Resistor for the LM317T Current Limiting Circuit
Resistors are only available in certain values - e.g. 5.6 Ohms and 6.8 Ohms, but not 6.2 Ohms. Below is a table of available resistor values together with the output current generated if each resistor is used in an LM317T current limiting circuit (
R = resistance,
I = current).
| R (Ohms) | 3.9 | 4.7 | 5.6 | 6.8 | 8.2 | 10 | 12 | 15 | 18 | 22 | 27 | 33 |
I (mA) | 321 | 266 | 223 | 184 | 152 | 125 | 104.2 | 83.3 | 69.4 | 56.8 | 46.3 | 37.9 |
Therefore using the table above we can see that to charge
1000mah AAA rechargeable batteries
with a current of 100ma, a 12 Ohm resistor would be perfect. A 15 Ohm resistor would reduce the current and slow down charging, a 10 Ohm resistor would increase the current and speed up charging.
Example Solar Battery Charger with LM317T
In this example we will make a solar charger using a
6 Volt 250ma Solar Panel to charge four
800mah AAA batteries. The batteries can be put into a couple of
2 x AAA battery holders and wired in series (link the positive output from one battery holder to the negative of the other).
This gives us 4 x 1.2 = 4.8 Volts with a capacity of 800mah - therefore we want a charging current of around 80ma. According to the table above, a
15 Ohm resistor gives a fixed current of 83.3 milliamps which will be perfect.
The power loss in the resistor is again given by Ohm's Law as I * I * R = 0.0833 * 0.0833 * 15 = 0.10 Watts, therefore we can safely use a standard 0.25 Watt 15 Ohm resistor.
For testing the circuit photographed below was built using
prototyping breadboard. The circuit is connected between the positive output of the
solar panel and the one free positive lead of the battery holders.
A
digital multimeter has been used to measure the actual current output by the circuit - in this case 84.1ma is a little higher than the expected 83.3ma since resistor values are not exact, and the
ADJ voltage output from the LM317T is not exactly 1.25 Volts.
Complete Current Limited Solar Battery Charger Circuit
The negative lead from the solar panel should be connected to the free negative input of the battery holders. The positive lead from the solar panel is connected to the positive input of the current limiting circuit, and the output from that circuit connected to the free positive lead of the battery holders.
You now have an improved
solar charger which will send a fixed amount of current (sunlight permitting) to the batteries. Charging from flat would take around 10 hours of sunlight in this worked example and you do not need to worry about overcharging your batteries.
A final enhancement would be to incorporate a
simple battery status monitor using a
Zener diode to light an LED when the battery voltage reaches the desired level.
Article Last Modified: 09:34, 30th Mar 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Solar Battery ChargingMake a solar charger for NiCd and NiMH rechargeable AA, AAA etc batteries
Article Last Modified: 09:43, 30th Jul 2007solar | educationUsing The LM317T With LED LightingUse an LM317T to regulate the current in LED lighting projects
Article Last Modified: 12:47, 12th Mar 2008lighting | electric circuitMake a Simple Battery Status MonitorMonitor battery status with this easy electric circuit project - no skill required!
Article Last Modified: 12:33, 16th Mar 2007storage | electric circuitLM317T Voltage Regulator ChipLearn about the LM317T and its uses in renewable energy projects
Article Last Modified: 14:35, 9th Sep 2008electronics | electric circuit12 Volt Battery Low Indicator LM741Plans for a battery low indicator for a 12 Volt battery using an LM741 operational amplifier
Article Last Modified: 10:17, 28th Jul 2007electronics | electric circuit | generalBasic 4 AA Solar Battery Charger PlansMake a simple solar charger for 4 AA rechargeable batteries
Article Last Modified: 09:43, 30th Jul 2007solar | educationLM317 Current CalculatorA handy online output current calculator for the LM317, LM338, and other linear voltage regulators
Article Last Modified: 12:47, 12th Mar 2008electric circuit | electronics | generalSolar Charge ControllerFind out more about Solar Charge Controllers
Article Last Modified: 11:12, 29th Oct 2009solar | electronics | electric circuitUsing The LM317T To Regulate VoltageUse an LM317T to regulate voltage in renewable energy projects
Article Last Modified: 15:04, 7th Mar 2008electric circuit | electronicsLM317 Voltage CalculatorA handy online output voltage calculator for the LM317, LM338, and other linear voltage regulators
Article Last Modified: 12:47, 12th Mar 2008electric circuit | electronics | general
|
|
|
