Make a Simple Battery Status Monitor
Make A Simple Battery Status Monitor
Monitor battery status with this easy electric circuit project - no skill required!
storage | electric circuitIt is essential that the
battery bank in a
renewable energy system is well looked after. This means that the
voltage of the battery bank must be known. It can be easily measured with a multimeter or a
voltmeter, however a fun and inexpensive project is to make a very simple
battery status monitor.
In a typical 12V system the voltage of the
battery bank can fluctuate from 10.6 Volts (below this the battery is very dead) when heavily depleted and under load, to as much as 15 Volts when being heavily charged. A healthy full 12V battery bank would usually have a voltage of around 12.6 Volts when not under a load and between 13-14 Volts when being charged correctly - i.e. not too quickly. Therefore it would be interesting to have an indication of the status of the battery bank using an
LED to show if it is being charged.
For this example we will use the arbitrary figure of 12.6 Volts to indicate
battery bank under charge however this could value could be set lower or higher according to your own needs and system configuration.
The Battery Status Monitor Introduction
The status monitor uses a
Zener Diode, a Light Emitting Diode (LED), and a
Resistor - components which can be bought for pennies each.
Each
Zener Diode has a specified
Zener voltage. If the voltage in the circuit is greater than the Zener voltage, then the
voltage drop (ie. the voltage reading across the diode) is equal to this Zener voltage. However, if the voltage in the circuit is less than the Zener voltage then no current flows. Therefore, if you put a Zener diode in series with an LED in a circuit, the LED will light if the circuit voltage is greater than the Zener voltage plus the voltage drop across the LED.
Making the Battery Status Monitor
We want our LED to light when the voltage of the
12V battery bank is 12.6 Volts or higher to indicate the batteries are being charged by our
renewable energy set-up. Let's use the following components:
1 x 8.2 Volt Zener diode.
1 x standard green LED (Specfications: maximum current 30mA, voltage drop 2.5 V).
In order to make the LED last as long as possible we will not use the maximum current - instead we will aim for around 15mA.
The total voltage drop across the Zener diode and LED will be 8.2+2.5=10.7 Volts. A
resistor is therefore required to prevent too much current getting to the LED and destroying it. The difference between the battery bank target voltage of 12.6 Volts, and the voltage dropped by the Zener and LED of 10.7 Volts is 1.9 Volts. These 1.9 Volts must be dropped across a suitable resisitor with a current of no more than 15mA - therefore using
Ohm's Law we find that resistance = 1.9 Volts / 0.015 Amps = 127 Ohms coincidently the exact value of a manufactured resistor. Normally you would select the resistor with the nearest value above the resistance value calculated with Ohm's Law.
Therefore add to the parts list for this project:
1 x 127 Ohm Resisitor.
Choosing Correctly Power Rated Components
We now need to check the
power dissipated in the Zener diode and resistor at different voltages so we can select suitably rated components, and check that the current flowing through the LED when the battery bank is at its maximum voltage is below the manufacturer recommended maximum.
If the
battery bank were to hit 15.5 Volts the voltage drop across the Zener diode would remain fixed at 8.2 Volts and the drop across the LED at 2.5 Volts, therefore the voltage drop across the resistor would increase to 15.5-8.2-2.5=4.8 Volts. Again using
Ohm's Law we find that the current through the resistor (and therefore through the LED) will rise to 4.8 Volts / 127 Ohms = 38mA. This is a little over the manufacturer recommended maximum current however, if your 12 Volt battery bank is regularly at 15.5 Volts the expense of replacing your little LED a couple of years early will pale into insignificance compared to the cost of the damage to your battery bank!
At a current of 38mA the power dissipated by the Zener diode will be 8.2 Volts * 0.038 = 0.31 Watts, and the power dissipated in the resistor will be 4.8 Volts * 0.038 = 0.18 Watts. Therefore a 500mW rated 8.2V Zener diode and a 1/4 Watt 127 Ohm resistor will be perfect.
Putting the Battery Status Monitor Together
There is no need to worry about soldering this together - the legs of the LED, resistor, and Zener diode can simply be twisted together. The last item you will need is:
1 x Length of One Amp bell wire (split along its length into two pieces of wire).
..which is very cheap - or you can cannibalise any other single-core insulated wire you have lying around. With a maximum current of 40mA flowing through it the wire does not need to be thick, but it is best to always use insulated wire to prevent accidently short-circuiting the battery bank.
The short leg on the LED (pictured above) is the cathode and is connected with the wire to the negative terminal of the battery.
The cathode of the Zener diode (pictured above) is marked with a stripe (silver in this example), however Zener diodes are placed into circuits in reverse, so next connect the positive anode (long leg) of the LED to the positive (no stripe) end of the Zener diode.
Finally the cathode of the Zener diode is connected to one leg of the resistor, and the other leg of the resisitor connected to the positive terminal of the battery bank with wire.
The green LED of the completed simple battery bank status monitor will now remain lit as long as the battery bank voltage stays above 12.6 Volts.
Developing the Battery Status Monitor Further
This
battery status monitor could not be more basic - it just indicates when the batteries have 12.6 Volts or more. However it would be very simple to extend the monitor to include an over-charge warning indicator when the voltage reaches say 14 Volts, and a battery healthy indicator which is lit as long as the voltage is over say 11.8 volts.
Simply recalculate the values of resistor and Zener diode required for each additional monitor and join each string of components in parallel to the battery to be monitored. The whole thing can be soldered together and built into a suitable box with the LEDs labelled so that everything looks tidy and you have a project to be proud of!
Buying Zener Diodes
Mixed packs of
Zener diodes are available in the
REUK Shop.
Article Last Modified: 12:33, 16th Mar 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Solar Battery Charger With LM317TFind out how to make a current controlled solar battery charger using an LM317T
Article Last Modified: 09:34, 30th Mar 2007solar | education | electric circuitLM741 OpAmp Voltage IndicatorPlans for a simple voltage high/low indicator built around an LM741 operational amplifier
Article Last Modified: 09:31, 8th Oct 2007electronics | electric circuit | generalInterconnecting Batteries for Battery BankFind out how best to connect batteries together into a battery bank
Article Last Modified: 13:53, 23rd Feb 2007storage12 Volt Battery Low Indicator LM741Plans for a battery low indicator for a 12 Volt battery using an LM741 operational amplifier
Article Last Modified: 10:17, 28th Jul 2007electronics | electric circuit | generalUsing The LM317T With LED LightingUse an LM317T to regulate the current in LED lighting projects
Article Last Modified: 12:47, 12th Mar 2008lighting | electric circuitBattery DesulfationFind out how to desulfate/desulphate and rejuvenate lead acid batteries
Article Last Modified: 16:56, 5th Oct 2009storage | electronicsDC Voltage Multiplier Circuit PlansBuild a circuit to boost the voltage of a DC power source using a MAX756
IC Chip
Article Last Modified: 09:06, 10th Jul 2008electric circuit | electronics | educationTL431 Battery Voltage MonitorMonitor the voltage of a battery or battery bank using an TL431 (aka LM431) shunt regulator
Article Last Modified: 16:42, 11th Jun 2007storage | electric circuit | electronicsWhat is a Zener DiodeFind out more about the Zener diode
Article Last Modified: 10:20, 10th Feb 2009electric circuit | educationLow Voltage Battery Disconnect CircuitsFind out more about low voltage battery disconnect (LVD) circuits - used to protect batteries
Article Last Modified: 15:04, 28th May 2009electric circuit | electronics | storage
|
|
|
