Light Dependent Resistor
Light Dependent Resistor
Find out more about LDRs and their use in renewable energy projects
electric circuit | solarA
Light Dependent Resistor (aka LDR, photoconductor, or photocell) is a device which has a resistance which varies according to the amount of light falling on its surface.
A typical light dependent resistor is pictured above together with (on the right hand side) its circuit diagram symbol. Different LDR's have different specifications, however the
LDR's we sell in the
REUK Shop are fairly standard and have a resistance in total darkness of 1 MOhm, and a resistance of a couple of kOhm in bright light (
10-20kOhm @ 10 lux, 2-4kOhm @ 100 lux).
Uses for Light Dependent Resistors
Light dependent resistors are a vital component in any
electric circuit which is to be turned on and off automatically according to the level of ambient light - for example, solar powered garden lights, and night security lighting.
An LDR can even be used in a simple remote control circuit using the backlight of a mobile phone to turn on a device - call the mobile from anywhere in the world, it lights up the LDR, and lighting (or a garden sprinkler) can be turned on remotely!
Light Dependent Resistor Circuits
There are two basic circuits using
light dependent resistors - the first is activated by darkness, the second is activated by light. The two circuits are very similar and just require an
LDR, some standard
resistors, a
variable resistor (aka potentiometer), and any small signal
transistor
In the circuit diagram above, the
LED lights up whenever the LDR is in
darkness. The 10K variable resistor is used to fine-tune the level of darkness required before the LED lights up. The 10K standard resistor can be changed as required to achieve the desired effect, although any replacement
must be at least
1K to protect the transistor from being damaged by excessive current.
By swapping the LDR over with the 10K and 10K variable resistors (as shown above), the circuit will be activated instead by light. Whenever sufficient light falls on the LDR (manually fine-tuned using the 10K variable resistor), the LED will light up.
Using an LDR in the Real World
The circuits shown above are not practically useful. In a real world circuit, the LED (and resistor) between the positive voltage input (Vin) and the collector (C) of the transistor would be replaced with the device to be powered.
Typically a
relay is used - particularly when the low voltage light detecting circuit is used to switch on (or off) a 240V mains powered device. A diagram of that part of the circuit is shown above. When darkness falls (if the LDR circuit is configured that way around), the
relay is triggered and the 240V device - for example a security light - switches on.
NEW For details of a more advanced light/dark sensor circuit click here to read our new article
LM741 Light/Dark Sensor Circuit. We have these circuits available for sale.
Article Last Modified: 09:26, 24th Oct 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
LM741 Light Dark Sensor CircuitBuild a light/dark sensing circuit to automatically turn on/off lights and other devices
Article Last Modified: 08:43, 2nd Nov 2007electronics | electric circuit | generalWhat is a TransistorA basic introduction to bipolar junction transistors
Article Last Modified: 11:15, 23rd Apr 2007electronics | educationSolar TrackerSet up solar panels to track the motion of the sun across the sky to maximise power output
Article Last Modified: 10:37, 9th Feb 2008solar | electronicsSolar Powered IrrigationWater your garden or allotment with a solar powered irrigation system
Article Last Modified: 15:58, 12th Jun 2008solar | waterSimple Solar Tracker ConceptMake a very simple sun tracker to maximise electricity generation from a PV solar panel
Article Last Modified: 10:37, 9th Feb 2008solar | electric circuit | generalLM741 OpAmp Voltage IndicatorPlans for a simple voltage high/low indicator built around an LM741 operational amplifier
Article Last Modified: 09:31, 8th Oct 2007electronics | electric circuit | generalResistor Colour CodesLearn how to identify different resistors with their colour code
Article Last Modified: 14:19, 22nd Feb 2007electric circuit | educationAutomatic Hen House Door Closer OpenerFind out how to put together a DIY automatic hen house door opener and closer
Article Last Modified: 11:47, 27th Jun 2009electric circuit | general | solarRepeat Timer CircuitMake a repeat timer circuit with large intervals between ON times
Article Last Modified: 09:58, 15th Aug 2009electric circuit | electronics | generalPIR SensorsFind out how to integrate PIR (passive infra red) sensors into renewable energy applications
Article Last Modified: 15:30, 2nd Oct 2007electronics | solar | general
|
|
|
