LM741 Light Dark Sensor Circuit
LM741 Light Dark Sensor Circuit
Build a light/dark sensing circuit to automatically turn on/off lights and other devices
electronics | electric circuit | generalA
light/dark sensing circuit is extremely useful and versatile in a wide range of
renewable energy projects from automatic lighting to security systems. In our article
Light Dependent Resistor we explained how an
LDR can be used in simple circuits to control devices according to the ambient levels of lighting - for example,
automatically turning on a lamp above a doorway at nighttime.
The circuits provided in that article were very basic and therefore not without their problems. The main problem is that the automatic turn-on is not
sharp - i.e. rather than switching the lamp on fully as soon as ambient levels of light fall to a fixed point, the lamp turns on slowly getting brighter and brighter as light levels fall. This is not a serious problem when controlling a lamp - in fact it may even be desirable - however when controlling other devices (such as a night vision camera) it is not optimal.
One way around this is to use a
relay, however a typical
12 Volt relay draws 300-500mW of power - a significant waste of energy when a
1 Watt LED spotlight for example is to be controlled.
LM741 Light/Dark Sensor Circuit (with Relay)
Above is a
schematic diagram of an
LM741 light/dark sensor circuit (from the excellent
741 Op-Amp Tutorial by
Tony van Roon).
The ECG128/NTE128
transistor stipulated can be substituted with any
NPN transistor rated at sufficient gain and current for the chosen
relay coil.
1st Nov 2007 Update - We have modified the schematic diagram above with the addition of a 220uF smoothing capacitor between the base of transistor Q1 and ground. Without this capacitor, the relay chatter (relay switching on and off many times per second) was terrible around the switch on/off light level. By adding the capacitor, relay chatter was completely eliminated.
According to the designer of this circuit, the relay will be closed
only when "
NO light falls on LDR1", however, in testing this circuit proved to work very well with the user able to adjust the
potentiometer (P1) to automatically close the relay at whatever light level they chose.
By swapping the postitions of the 10K
resistor (R1) and the
LDR (LDR1), the relay will be closed when the LDR is under light rather than under darkness. Therefore a device can automatically be switched off at nighttime.
Since this circuit still contains a
relay we need to make some changes* to reduce the amount of power to make it more suitable for
renewable energy powered low-current applications.
*
Where devices of more than a couple of Amps are to be powered, the energy loss in the relay becomes insignificant and so the above illustated circuit should be used as is.
Modification One (Low Current Applications <200mA)
If this circuit is to be used to provide
<200mA of current (for example, to power just ONE 12V MR16 LED spotlight with around 100mA), the relay can be removed altogether as illustrated below:
Modification Two (Medium Current Applications <2Amps)
If more current is required - for example to power a string of LED spotlights - the transistor can be replaced by a
MOSFET. A MOSFET is similar to a transistor, but it can carry much
more current. In our testing we used an
STP36NF06 MOSFET since that's what we had lying around.
The MOSFET circuit requires just a couple of small modifications to the original circuit as illustrated below:
Buy a Light/Dark Sensor Circuit
Since the vast majority of people do not have the necessary expertise and equipment to put together one of these circuits, we are happy to put one together for you according to your exact needs.
The MOSFET version of the circuit (suitable for maximum total output currents of 2 to 3 Amps) is now available from the
REUK Shop and is pictured above. Click here for more information and to make a purchase:
Light/Dark Sensor Circuit (Low Current).
NEW - We now also have the
relay version of the circuit (suitable for maximum total output currents of 10 to 12 Amps) and it is also available in the REUK Shop:
Light/Dark Sensor Circuit (Relay).
Tailormade Circuitry
If you require a bespoke
light/dark sensor circuit - for example, one which activates in
light rather than in darkness contact
neil@reuk.co.uk directly with details of your requirements. Prices start from around
£10 per circuit including all components.
Article Last Modified: 08:43, 2nd Nov 2007Comment on this Article
If you have any comments on this article, please email them to
neil@reuk.co.uk.
Recommended Related Articles
People who read this article also enjoyed the following articles:
Light Dependent ResistorFind out more about LDRs and their use in renewable energy projects
Article Last Modified: 09:26, 24th Oct 2007electric circuit | solarLM741 OpAmp Voltage IndicatorPlans for a simple voltage high/low indicator built around an LM741 operational amplifier
Article Last Modified: 09:31, 8th Oct 2007electronics | electric circuit | generalUsing The LM317T With LED LightingUse an LM317T to regulate the current in LED lighting projects
Article Last Modified: 12:47, 12th Mar 2008lighting | electric circuitTimer Circuits With 4060BBuild a reliable timer to switch devices on and off - from 30 seconds to 24 hours
Article Last Modified: 09:58, 15th Aug 2009electronics | electric circuitLED Dimmer CircuitFind out how to put together a simple but efficient PWM dimmer circuit for LEDs
Article Last Modified: 16:03, 21st Nov 2007lighting | electronics | electric circuitSolar Battery Charger With LM317TFind out how to make a current controlled solar battery charger using an LM317T
Article Last Modified: 09:34, 30th Mar 2007solar | education | electric circuitWhat is a TransistorA basic introduction to bipolar junction transistors
Article Last Modified: 11:15, 23rd Apr 2007electronics | education12 Volt Battery Low Indicator LM741Plans for a battery low indicator for a 12 Volt battery using an LM741 operational amplifier
Article Last Modified: 10:17, 28th Jul 2007electronics | electric circuit | generalMultiple PIR Sensor CircuitsConnecting more than one PIR sensors in a circuit
Article Last Modified: 17:00, 9th Mar 2009electronics | electric circuit | generalMake a Simple Battery Status MonitorMonitor battery status with this easy electric circuit project - no skill required!
Article Last Modified: 12:33, 16th Mar 2007storage | electric circuit
|
|
|
